EFI System Firmware Update Package Install Instructions

Intel (R) Server Boards X38ML, Intel (R) Server Systems SR1520ML
Firmware Update Package Update Instructions 

Released - November 29, 2010

*************************************************************************************
This Update package includes the following system software updates:

  System BIOS  - 52
  BMC Firmware - 15
  FRUSDR       - 1.06

Important NOTES: 

- All the updates provided in this package are EFI based (unless otherwise noted).To 
  run these updates, you must boot the system to the embedded EFI shell and then 
  access the USB device or hard disk containing the system software udpates.


*************************************************************************************
                       SYSTEM REQUIREMENTS
*************************************************************************************
The contents of this update package is used to update the System Firmware for 
the following Intel Server Products only:

  - Intel(R) Server Board X38ML
  - Intel(R) Server System SR1520ML

*************************************************************************************
                 Standard Update Procedure from the embedded EFI Shell
*************************************************************************************

- Unzip package and copy all files to a folder in USB disk on key
- Insert USB disk on key to server / workstation USB port
- Boot Server to EFI shell
- Run command "map -r" in EFI shell to mount USB disk on key
- Run command "fs0:" to change folder to USB disk on key, USB key may also mount to
  fs1:. The number of "fs" is dependent on the result of command "map -r"
- Change folder to the folder storing the firmware package
- Run command "startup.nsh" to start updating all the firwmares and BIOS


Warning: 
!!Do NOT reboot or shut down power from your system during following software update!!


*************************************************************************************
If you want to update single components like BMC/BIOS separately, please go to the 
root folder and execute the specified scripts separately, and follow below 
update process to ensure trouble free update from BIOS R0052, BMC 15, FRUSDR 1.06:
  1) BMC firmware update to 15
  2) BIOS update to R0052
  3) FRUSDR update to 1.06
*************************************************************************************

*************************************************************************************
                                Update BMC Firmware
*************************************************************************************
1) Boot the system to the EFI shell and go to root folder
2) At the shell prompt, run "BMC15.nsh" to start BMC Firmware update
3) When complete, go to the BIOS update section described below, or power off the 
   system and cycle AC power before continuing.

*************************************************************************************
                                 Update System BIOS 
*************************************************************************************

1) Boot the system to the EFI shell and go to root folder
2) At the shell prompt, run "BIOS52.nsh" to start BIOS update
3) When complete, reboot the system and enter BIOS Setup by pressing the F2 Key during
   POST 
4) Verify the BIOS string on main BIOS menu shows the BIOS revision as S3200X38.86B.00.00.0052
5) Press F9 to load defaults and press F10 to save and reset the system

The BIOS update is complete. reboot the server 

Note:
See BIOS_Recovery_Instructions on BIOS Release Notes for the steps to recover failed BIOS.

*************************************************************************************
                                      Update FRUSDR
*************************************************************************************

1) Boot the system to the EFI shell and go to root folder
2) At the EFI command prompt, run "FWB106.nsh" to start FRUSDR update
3) Answer questions and enter desired information when prompted.
4) When complete, reboot the system by front control panel

*************************************************************************************
                                    Verifying updates
*************************************************************************************

1)  During POST, hit the F2 Key when prompted to access the BIOS Setup Utility
2)  Hit the F9 key to load BIOS Defaults
3)  At the MAIN menu verify the BIOS revision is 'S3200X38.86B.00.00.0052'
4)  Move cursor to the SERVER MANAGEMENT Menu
5)  Move cursor down to the SYSTEM INFORMATION Option and hit Enter
6)  Verify the BMC Firmware revision 
7)  Verify the SDR Revision 
8) Hit the F10 Key to save changes and Exit


The System Software Update is Complete.