================================================================================ Intel(R) Server Platform S1200BT System Firmware Update Package for Intel(R) Deployment Assistant, Intel(R) One Boot Flash Update Utility, The embedded EFI Shell, Windows* Preboot Execution Environment ================================================================================ Intel Enterprise Platform & Services Division - Marketing Intel Corporation 2111 N.E. 25th Avenue, Hillsboro, OR 97124 USA ================================================================================ DATE : March 14, 2012 TO : Intel(R) Server Board S1200BTL SUBJECT : Release Notes for System Firmware Update Package ================================================================================ ABOUT THIS RELEASE ================================================================================ BIOS : S1200BT.86B.01.00.0035.030220120927 ME : ME_02_02_00_036 BMC : 1.13 FRUSDR : 1.14 Note: There is no separate firmware of the Hot-Swap Backplane FUP4X35HSBP for Intel(R) Server Board S1200BT server system. The Hot-Swap Backplane firmware is integrated into the BMC firmware. ================================================================================ Support Platforms and Dependency ================================================================================ This update package is for Intel(R) Server Board S1200BTL and Intel(R) Server System R1304BTLSFAN and Intel(R) Server System R1304BTLSHBN and Intel(R) Server System P4304BTLSFCN and Intel(R) Server System P4304BTLSHCN. Intel(R) Server Platform S1200BT family Processors supported: Intel(R) Xeon(R) Processor E3-1200 series, 2nd Generation of Intel(R) Core(TM) i3 processor, Intel(R) Xeon processor E3-1200V2 series and 3rd Generation of Intel(R) Core(TM) i3 processor. Microcode update versions: CPUID Version Status Intel(R) Xeon processor E3-1200 series D1 stepping: 0x00000028 CPUID = 0x206a6 Intel(R) Xeon processor E3-1200 series D2 stepping: 0x00000025 CPUID = 0x206a7 Intel(R) Xeon processor E3-1200 series Q0 stepping: 0x00000025 CPUID = 0x206a7 Intel(R) Xeon processor E3-1200V2 series B0 stepping: 0x0000000C CPUID = 0x306a2 Intel(R) Xeon processor E3-1200V2 series C0 stepping: 0x00000007 CPUID = 0x306a4 Intel(R) Xeon processor E3-1200V2 series K0 stepping: 0x00000009 CPUID = 0x306a5 Intel(R) Xeon processor E3-1200V2 series D0 stepping: 0x00000004 CPUID = 0x306a6 Intel(R) Xeon processor E3-1200V2 series E0 stepping: 0x0000000C CPUID = 0x306a8 Intel(R) Xeon processor E3-1200V2 series E1 stepping: 0x0000000C CPUID = 0x206a9 On-Board Component Option ROM Versions: Integrated BMC Matrox VGA (S1200BTL) : VBE BIOS V3.8 SM712 Video Option ROM (S1200BTS) : v2.24.03r Intel Rapid Storage Technology : v11.0.0.1339 ESRT2 SWRAID (Legacy) Option ROM : A.10.02251631I Intel iSCSI Boot Oprom : v2.7.53 82579 EEPROM Version : v1.0 82579 PXE Version : Intel(R) Boot Agent GE v1.3.65 82574L PXE Version : Intel(R) Boot Agent GE v1.3.65 Memory Reference Code Version : v1.1.0 TXT Framework BIOS Reference Code : V1.0.0 SNB ACPI Reference Code Version : V1.0.0 System Agent Reference Code Version: V1.1.0 Intel(R) SPS ME Firmware Package : ME_02_02_00_036 ================================================================================ Update system firmware from Intel server EFI shell by the following steps: - Download Intel server system firmware update package from support.intel.com - Unzip package and copy all files to root folder in USB disk on key - Insert USB disk on key to server USB port - Reboot server, system will start BIOS/BMC/FRUSDR update automatically In case for some reason or you didn't put unzipped package under root folder of USB key, you can do it by: - Reboot server to EFI shell manually - Run command "map -r" in EFI shell to mount USB disk on key - Run command "fs0:" to change folder to USB disk on key, USB key may also mount to fs1:. The number of "fs" is dependent on the result of command "map -r" - Change folder to the folder storing the firmware package - Run command "startup.nsh" to start firmware update process Warning: !!Do NOT reboot or shut down power from your system during following software update!! Please refer to "EFI_Instructions.pdf" in this firmware package for a quick guide to use the EFI commands ================================================================================ BIOS Change in release R0035 ================================================================================ - Fixed: Erros logged in SEL when certain add-in video cards were installed. - Fixed: SAS module RMS2AF040 is not detected when Intel(R) E3-1200V2 series procesoors are installed. - Fixed: When memory is installed in dual mode, BIOS setup reports the memory as Independent mode. - Fixed: 4k sector HDD's set as non-bootable causes the system to take 10 minutes to boot. - Fixed: Intel(R) RAID controller RS5DB080 cannot be detected in the UEFI environment when EFI optimized Boot is enabled in BIOS setup. - Fixed: With Front Panel Lockout enabled in BIOS setup, the front panel NMI button is still functional. - Fixed: Server Management Settings cannot be configured using the SysCfg utility. ================================================================================ BIOS Change in Release R0032 ================================================================================ - Fixed: ME might enter recovery mode after some specific scenario on Intel(R) Server Board S1200BTS. - Fixed: Console redirection item is not shown correctly in BIOS setup page. - Fixed: A bug relate to NMI function. - Fixed: Adaptec 6445 compatible issue with Intel(R) Server Board S1200BTL. - Fixed: Integrated BMC and RMM4 NIC settings in BIOS setup are gone after load default. Other: - Update Intel(R) Rapid Storage Option Rom to the version v10.6.0.1091 ================================================================================ BIOS Change in Release R0030 ================================================================================ - Fixed: Incorrect error message in BIOS setup Error Manager after flashing the BIOS. - Fixed: With TXT enabled, a USB keyboard may become non-functional after as USB flash drive is inserted/removed. - Fixed: RMM4 password cannot be set in BIOS Setup. - Fixed: When multiple USB devices are connecte via a hub, some USB devices may not be detected by BIOS. Other: Added: Enabled ACPI S3 capability. ================================================================================ BIOS Change in Release R0029 ================================================================================ - Fixed: SMBIOS flash data will be lost after a BIOS update. - Fixed: System hangs when getting SMBIOS flash data after the second reboot. - Fixed: DMIedit utility cannot write Board S/N and PBA in EFIx64 and Microsoft* Windows*. ================================================================================ BIOS Change in Release R0028 ================================================================================ - Fixed: Hotplug not support under AHCI mode - Fixed: Tool load dafault, board won't reboot w/ EUPLOT6 enabled. - Fixed: RS2BL040 in S1200BTL: Pressing Ctrl+G won't show RAID BIOS Console 2. - Fixed: Windows* 2008 R2 can not be installed properly with NIC ROM disabled - Fixed: Ambient Sensor of BIOS is wrong. - Fixed: The DIMM population Map value is incorrect under smbios log - Fixed: A console redirection issue which system will hang when pressing "Ctrl+I" via remote console - Fixed: Potential memory overflow in BDS module - Fixed: Automatically recovery NVRAM if corrupted - Fixed: Update microcode to revision 17 ================================================================================ BIOS Change in Release R0027 ================================================================================ - Fixed: one memory allocation bug - Fixed: Klokwork issues - Enhance error handling logic in CSM module in case of legacy resource allocation failure - Add more NV variables to the protected NV variable list for NV reclaim - Fixed: Addendum to PVMode broken using BIOS 24. - Fixed: The Total Width value is error at Type 17 under smbios log - Fixed: After reset, the system would halt at 0x15 about 20 sec - Fixed: The CPU voltage value is error under smbios log - Fixed: OEMID and OEM TableID could not display correctly within ACPI Table ================================================================================ BIOS Change in Release R0026 ================================================================================ - Fixed: The System may hang during the OS rebooting test ================================================================================ BIOS Change in Release R0025 ================================================================================ - N/A ================================================================================ BIOS changes in release R0024 ================================================================================ - Fixed: Server Active Console is not available on the remote console. - Fixed: Bios settings cannot be changed after running 'syscfg /bldfs' to load Bios defaults. - Fixed: Microsoft Windows 2008* R2 64 bit fails to load when using an LSI* 20320 RAID adapter. - Fixed: BIOS Admin password gets cleared after loading BIOS defaults . Other: - Updated: Fan Speed Control. - Enabled: Global reset after ME update. - Updated: SM712 VBIOS to version2.24.03n ================================================================================ BIOS Changes in release R0022 ================================================================================ Issues Fixed: - Fixed: System hangs when there is only one hard disk in the boot order device type. Fixed: System Acoustics and Performance: Selectable options are incorrect. Fixed: SE Video has no output from slot5 using a VGA video card. Fixed: Admin Password is cleared after loading BIOS defaults. Fixed: Cannot boot from a USB device that emulates a CD-ROM. Fixed: The Help Text description of BIOS items are not consistent. Fixed: ME update displays 0.0.0.0 in BIOS setup after update. Fixed: System Boot Timeout is incorrect; the default should be zero. Fixed: Microsoft* Windows* installation to iSCSI target fails. ================================================================================ BIOS Changes in release R0018 ================================================================================ Issues Fixed: - Initial production BIOS release for the Intel(R) Server Board S1200BTL. =============================================================================== ME Changes in release 02_02_00_036 =============================================================================== - Fixed: Sometimes the platform is not booting when the Operational image is corrupted, ME is not responding. - Fixed: MEInfo does not show ME features set when ME is in Recovery mode. Also Recovery image version is not shown. - Fixed: HECI reset is not poperly supported when ME is in Recovery Mode. - Fixed: NM does not support DCMI1.1 commands defined in IPMI-spec. - Fixed: VHD dynamic fusing is not working as expected. - Fixed: When ME FW configured for operating in All Sx states and platform powered up from G3 to S5 power mode. ME FW will stuck during ME reset executed in recovery mode. - Fixed: Get ME-BIOS Interface Version (HECI command) is not implemented in Recovery mode. - Fixed: After Direct Update (without ME reset) Get FW Version HECI command returns version of the former image. - Fixed: General NM Presets configuration in FITc application does not contain all S1200BT options. - Fixed: There are power flow scenarios where ME recovery jumper does not reset ME configuration to factory defaults. The jumper is supposed to cause ME to enter recovery boot loader code and reset ME firmware configuration to factory defaults. The later sometimes does not occur. - Fixed: Firmware Heartbeat in HECI-1 Extended FW Status register is not incremented as it is described in "ME-BIOS-SPS Firmware Interface Specification". - Fixed: After sending the "ME Reset to defaults" IPMI command ME stops responding to IPMI commands for 8 seconds. - Fixed: When Diagnostics service is enabled and Diagnostics Console is disconnected switching to Recovery via IPMI or HECI commands takes about 5 seconds. - Fixed: Diagnostics console Compliance Test 1.2. "BIOS HECI Initialization message" gives unspecified state of "HECI Initialization message". - Fixed: In case when flash erase limit has been reached ME generates ME Firmware Health event with the event data 3 equal to 0xD5 instead of 0x01. - Fixed: Resuming platform after S3 state fails on Intel(R) Xeon(R) processor E5-4600/2600/2400/1600/1400 v2 product families, also Dynamic Fusing will fail during Sx -> S0 transition. - Fixed: If ME reset will be performed after AC cycle, then HMRFPO_LOCK HECI message will return invalid Nonce causing Direct Update failure. - Fixed: If invalid image will be used for Direct Update and global reset will be issued for ME reset, then ME will state in Recovery mode and repairing broken image using Direct Update will fail (HMRFPO_LOCK HECI message will return invalid Nonce). - Fixed: Active policy with Policy Exception Actions = 1 (Shutdown system) may sometimes unexpectedly shutdown platform even when power is properly capped. - Fixed: Power Sensor Address set to 0x10 instead of 0x20 in Alert Immediate NM Health Event. - Fixed: Power Reading polling is not working when Scan Period is set to 250 ms for BMC set as a Power Reading source. - Fixed: Node Manager Exception Events are sent after every Correction Time. This behavior can cause SEL overflow. - Fixed: Unexpected shutdown during aggressive policy operation. Sometimes aggressive policy could cause platform shutdown even if power limit was reached. - Fixed: Node Manager Exception Event "Policy Correction Time Exceeded" comes after double correction time instead of one correction time. - Added: Thermal policies support was added in current release. - Added: This release contains fixes in the ME recovery boot loader section. ================================================================================ ME Changes in release ME_02_00_09_032 ================================================================================ Issue Fixed: - Sometimes, when ME is configured for operating in all Sx states and while platform is performing transition from G3 to S5 and later from S5 to S0, ME could be unexpectedly reset. - Unexpected ME reset could appear during NM communication with some specific PSU, as a result of which the CPU throttling statistics could be violated. ================================================================================ ME Changes in release SPS_02_00_08_015_0 ================================================================================ - Initial production ME release for the Intel(R) Server Board S1200BTL =============================================================================== BMC Changes in release 1.13 =============================================================================== - Fixed: rKVM/Remote media client not tracking source port forwards - Fixed: Cannot ping SUT with VLAN IP after AC Cycle and completed POST. - Fixed: Diagnostic tests are unclear what they are supposed to do - Fixed: OEM Timestamp and OEM Non Timestamped events not decoded correctly in Embedded Web Console and Embedded Web Console SEL dumps - Fixed: Embedded Web Console SEL display page does not display the specific DIMM, CPU, and PCIE information for all DIMM, CPU, and PCIE faults - Fixed: The BIOS does not save the BMC RMM4 IP configuration if NIC1 IP configuration also changed - Fixed: In the Embedded Web Console, if the sensor is in "N/A" status, the indicative string is "OK" and should be "Unknown". ================================================================================ BMC Changes in release 1.12 ================================================================================ - Upgrade HSBP Firemare to 00.12 Issue Fixed: - Mount ISO image to RMM4 may cause "error reading video data" issue on S1200BT when using some network switches ================================================================================ BMC Changes in release 1.10 ================================================================================ Issue Fixed: - SEL keeps reporting rebuild/remap in progress,Deasserted/Asserted,and finally fills up the SEL - HSBP PSOC FW reports drive presence not correct - The Connection to RMM4 from IASC will lost sometimes ================================================================================ BMC Changes in release 1.09 ================================================================================ Issue Fixed: - Remove UNC and UC threshold for VBAT sensor. ================================================================================ BMC Changes in release 1.08 ================================================================================ Issue Fixed: - System Fan RPM 0 after runing sometime on Intel(R) Server System R1304BTLSHBN. ================================================================================ BMC Changes in release 1.07 ================================================================================ Issue Fixed: - BMC user SOL payload enable/disable status can't be saved across BMC reset issue. - HSBP PSOC FW reported drive presence not correct issue. ================================================================================ BMC Changes in release 1.05 ================================================================================ Issue Fixed: - Integrated BMC SMBus ACK hold time delay issue. ================================================================================ BMC Changes in release 1.04 ================================================================================ Issue Fixed: - Fixed 4 HSBP problems via including HSBP 0.6 ================================================================================ BMC Changes in release 1.04 ================================================================================ Issue Fixed: - Fixed 4 HSBP problems via including HSBP 0.6 ================================================================================ BMC Changes in release 1.03 ================================================================================ Issues Fixed: - Initial production BMC release for the Intel(R) Server Board S1200BTL. ================================================================================ FRUSDR Changes in release 1.14 ================================================================================ Feature Added: - Add PV_VCC_SENSOR(0xE0) to support Intel(R) Xeon(R) E3-1200V2 Processors. - Correct the comment for BB +3V Vbat record. ================================================================================ FRUSDR Changes in release 1.13 ================================================================================ Feature Added: - Add different stepping to support Intel(R) Xeon(R) E3-1200V2 Processors. Issue Fixed: - Can not detect "Intel(R) Xeon(R) E3-1200V2 Processors" during the processing of FRUSDR update ================================================================================= FRUSDR Changes in release 1.12 ================================================================================= - Add Intel(R) Xeon(R) E3-1200V2 Processors detection. ================================================================================ FRUSDR Changes in release 1.11 ================================================================================ Feature Added: - Divide sensor number 04h record into two, one is with chassis intrusion event mask, another is not. ================================================================================ FRUSDR Changes in release 1.10 ================================================================================ Feature Added: - Add Front Panel NMI tag - Modify sensor type and event reading type for Mem P1 Thermal Trip. - Add auto-detection for the next generation processor ================================================================================ FRUSDR Changes in release 1.09 ================================================================================ Issue Fixed: - Fan sensor multiplier for the 3rd party chassis. - Remove displaying the prompt if no front panel sensor is detected. ================================================================================ FRUSDR Changes in releaes 1.08 ================================================================================ Issue Fixed: - 3V VBat upper critical/non-critical threshold value to FFh/FEh. ================================================================================ FRUSDR Changes in release 1.07 ================================================================================ Issue Fixed: - Add checking prod id mechanism. - Correct OTHER chassis referring to front panel for stepwise. - Modify fan speed range for 3rd party chassis. - Update SDR as per Bromolow FSC Config Sheet.xls(v2.0). - Change display for board name to S1200BTL and chassis code name. - Modify Node Manager discovery record to support Node Manager Capabilities and Threshold sensor. ================================================================================= FRUSDR Changes in release 1.05 ================================================================================= Issue Fixed: - Modify entity instance for entity id 07 to identical. ================================================================================= FRUSDR Changes in release 1.04 ================================================================================= Issue Fixed: - Change P4304XXSHBN domain 3 stepwise fan speed control value. - Change HSBP target temperature for clamping to 52 degree. - Add an OEM Node Manager Discovery record for SDR. - Update SDR as per Bromolow FSC Config Sheet.xls(v1.9). ================================================================================= FRUSDR Changes in release 1.03 ================================================================================= Issue Fixed: - Unique the entity instance for each entity id. - Add a condition for CPU fan shouldn't install for R1304XXS chassis detection. - Update FRUSDR utility to FRUSDR10.0-Build05. - Change file name to align BMC version. ================================================================================ FRUSDR Changes in release 11 ================================================================================ Issues Fixed: - Initial production FRU/SDR release for the Intel(R) Server Board S1200BTL. ============================================================================= LEGAL INFORMATION ============================================================================= Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Intel is a registered trademark of Intel Corporation. *Other names and brands are the property of their respective owners. Copyright (c) 2012 Intel Corporation. A portion of this firmware is open source code, which falls under the GPL 2.0 license. [END OF RELEASE NOTES]