================================================================================ Intel(R) Server Board S2400GP Family Intel(R) Server System P4000GP Family Firmware Update Package for Intel(R) Deployment Assistant, Intel(R) One Boot Flash Update Utility, The embedded EFI Shell, Windows* Preboot Execution Environment ================================================================================ Intel Enterprise Platform & Services Division - Marketing Intel Corporation 2111 N.E. 25th Avenue, Hillsboro, OR 97124 USA ================================================================================ DATE : June 29, 2012 TO : Intel(R) Server Board S2400GP Family Intel(R) Server System P4000GP Family customers SUBJECT : Release Notes for System Firmware Update Package ================================================================================ ABOUT THIS RELEASE ================================================================================ BIOS : 01.03.0002 ME : 02.01.05.107 BMC : 1.10.3560 FRUSDR : 1.05 ================================================================================ Support Platforms and Dependency ================================================================================ Processors supported: Intel(R) Xeon processor E5-2600/2400 series Microcode update versions: Intel(R) Xeon processor E5-2600/2400 series C0 stepping: 0x80000513 CPUID = 0x206D5 Intel(R) Xeon processor E5-2600/2400 series C1 stepping: 0x80000615 CPUID = 0x206D6 Intel(R) Xeon processor E5-2600/2400 series C2 stepping: 0x8000070A CPUID = 0x206D7 Production boards: Product Fab Version S2400GP Fab2 or above Before update to the BIOS/ME/BMC/FRUSDR contained in the package, please check in BIOS set up menu and verify your board has below BIOS/ME/BMC/FRUSDR versions installed: - BIOS 01.02.2002, or later Version - ME 02.01.05.69 or later Version - BMC 01.00.2812 or later Version - FRUSDR 09 or later version The following update process must be followed to ensure a trouble free update. 1. BMC firmware to 1.00 or later 2. BIOS 01.01.1002 or later 3. Manageability Engine (ME) firmware 02.01.05.69 or later 4. Latest FRU/SDR package specific to the baseboard. ================================================================================ System Firmware Update Package Usage instructions ================================================================================ This package can be updated using one of the following methods: - The embedded UEFI shell - Intel(R) Deployment Assistant - Windows* or Linux* operating system using Intel(R) One-boot Flash Update (OFU) V11.0 Build 9 or later) - Windows* Preboot Execution Environment (WinPE) To Update from the embedded EFI Shell update system firmware from Intel server EFI shell by the following steps: - Download Intel server system firmware update package from http://www.intel.com/support/ - Unzip package and copy all files to root folder in USB disk on key - Insert USB disk on key to server USB port - Reboot server, system will start BIOS/BMC/FRUSDR update automatically If case for some reason or you didn't put unzipped package under root folder of USB key, you can do it by: - Reboot server to EFI shell manually - Run command "map -r" in EFI shell to mount USB disk on key - Run command "fs0:" to change folder to USB disk on key, USB key may also mount to fs1:. The number of "fs" is dependent on the result of command "map -r" - Change folder to the folder storing the firmware package - Run command "startup.nsh" to start firmware update process Please refer to "EFI_Instructions.pdf" in this firmware package for a quick guide to use the EFI commands To Update from Intel(R) Deployment Assistant (IDA) The Intel(R) Deployment Assistant software is easy to use and is present on the "Intel(R) Server Deployment & Management" DVD shipped with the system. User can download the latest version IDA CD ISO image from http://www.intel.com/support/ To use the IDA CD to update the system firmware: - Boot server with IDA CD - Select "Get System Updates" - Choose one of the three options . From http://www.intel.com/support/ Automatically downloads the latest Firmware Update Package from Intel It requires Internet connection Enter your local IP address and proxy configuration Click "Next" to start the download and update process . From my network Download the latest Firmware Update Package from http://www.intel.com/support/ and copy it to a Windows* shared folder Enter your local IP address, the Windows* file server name, and a Windows user name and password Select the firmware package in pop-up window Click "Next" to start the update process . From USB Disk on Key or Hard Disk Download the latest Firmware Update Package from http://www.intel.com/support/ and copy it to a USB key, then insert the key into the server USB port Click "Browse" Select the firmware package in pop-up window Click "Next" to start the update process Note: The Firmware Update Package is in the ZIP file format. Do not unzip before copying to a Windows* shared folder or USB disk. To update from Windows* and Linux* or operating systems using the Intel(R) One Boot Flash Update Utility (OFU) Intel(R) One boot Flash Update utility can be downloaded from http://www.intel.com/support/ and it is part of the "BIOS, Firmware Update & Configuration Utilities" for Windows* and Linux*. Please refer to Intel OFU user guide about the details of installation and usage of OFU. Use OFU to update system firmware by the following steps: - Install OFU on Windows* or Linux* system - Download the latest firmware update package from http://www.intel.com/support/ - Unzip package to a folder - Run the following command in Windows* command line/Linux* terminal window: :\flashupdt -u \flashupdt.cfg To update from Windows* Preboot Execution Environment (WinPE) The System Firmware Update Package can be inserted to Windows* PE customized image for creating a bootable Windows* PE CD. User is able to update system firmware from customized WinPE CD by the following steps: - Boot server with customized WinPE CD - Run script "WinPE21_x64_Update.bat" or "WinPE20_x86_Update.bat" (name may be varied depends on your own customization) Note: 1. The Intel(R) OFU utility is case sensitive. Therefore, when you transfer the Firmware Update Package using USB key from a Microsoft Windows* system to a Linux environment, you must first extract under the Linux* environment. Otherwise, you will need to mount the USB key manually with 'vfat' option under Linux to avoid conversion from upper case to lower case and vice versa. 2. To make Intel(R) OFU utility run properly under x86 or x64 OS, you have to read OFU releaenotes on known issues for OFU installation. 3. In this SFUP package, Intel only provide batch file "WinPE_x86_Update.bat" for WinPE2.0 32 bit solution "WinPE_x64_Update.bat" for WinPE2.1/3.0 64 bit solution as an example. Please refer to white paper "White Paper-Intel Server Utilities Procedure for WinPE.pdf" for details on building your own customized WinPE CD. 4. Windows PE 2.0 - built from Windows Vista SP1 32bit or EM64T 5. Windows PE 2.1 - built from Windows Vista SP1 or Windows Server 2008, EM64T 6. Windows PE 3.1 - built from Windows Server 2008R2, EM64T 7. Microsoft IPMI driver is loaded by default from WinPE CD, if you want to use Intel IPMI driver instead of MS IPMI driver for firmware update, you can un-install Microsoft IPMI driver by: Devicesetup.exe ¨Cv remove *IPI0001 Note: IPI0001 is the device ID for Microsoft IPMI driver. ================================================================================= BIOS changes since 01.02.0006 ================================================================================= - Fixed: NIC Information can not be saved in the Sysinfo log file and it cannot be retrieved or set using the syscfg utility. - Fixed: If Remotely redirecting an ISO image from a client and the target system is restarted, the target system will automatically boot to the redirected ISO image and start an OS installation. - Fixed: On GUID based partitions any SMI call freezes system. - Fixed: When the baseboard LAN IPV6 is enabled in BIOS setup, the RMM4 configuration is greyed out. - Fixed: Unable to disable onboard NIC ports in BIOS setup. - Fixed: C1E is disabled when both C3 and C6 processor Cstates are disabled in BIOS setup. - Fixed: In BIOS setup, Serial B is incorrectly set to disabled by default and cannot be enabled. - Fixed: TPM Admin Control option should be disabled (grayed out) when the BIOS admin password is not set. - Fixed: Onboard NIC2 MAC address can not be shown correctly and it can't boot to PXE from NIC2 on Intel(R) Server Board S2400EP. - Fixed: Update add-in video output policy - Fixed: PCIe slot 5 max link width can only be detectes as x4 on Intel(R) Server Board S1400FP. - Fixed: EFI network stack incorrectly uses Mezzenine NIC port. - Fixed: FRB2 timer will reset the system after 6 minutes when entering BIOS Setup via the boot menu. - Fixed: System cannot enter EUP Lot6 deep sleep mode. - Fixed: PCIe link speed changes occur without logging a SEL event. - Fixed: During POST, populeated PCIe slots numbers are incorrectly identified. - Fixed: Cannot change Serial Port A to IRQ3 on Intel(R) Server Board S2600JF. - Fixed: NIC1 and NIC2 cannot be disabled on Intel(R) Server Board S2400SC. - Fixed: ACPI errors are reported in dmesg.log in SUSE* Linux* 11 SP2 RC x64. - Fixed: W2600CR Windows* 7 WHQL cert Failure - Single computer Display object Test Failure ================================================================================ ME changes since 02.01.05.91 ================================================================================ - Fixed: FW may hang in initialization state after the update of entire ME region is interrupted by AC loss. - None of the available ME resets (AC cycle or Global Reset or Power Button Override) can get ME out of the error condition, only reflashing ME image. - Fixed: FW may become unresponsive after switching from Recovery to Operational (e.g. during Direct Update). - Global Reset or Power Button Override can’t get ME out of the error condition. ================================================================================ BMC Changes since release 1.04.2896 ================================================================================ - Fixed: Updated FRUSDR files. - S2400BB to version 0.09 - S2600CP to version 1.06 - S2600CO to version 1.07 - W2600CR to version 1.07 - S2400EP to version 1.00 - S2600IP to version 1.07 - S2600JF to version 1.07 - S2400LP to version 1.06 - S2600CP to version 1.07 - S2600CO to version 1.08 - W2600CR/S2600IP to version 1.08 - S2400GP to version 1.05 - S1600JP to version 0.05 - S2600JF to version 1.08 - S4600LH to version 0.12 - S2600WP to version 1.05 - S2600GZ/S2600GL to version 1.03 - Fixed: Adjust RGMII Tx clock delay to -250ps for S1400SP according to SI requirement - Fixed: Command OEM Get Reading. will now return units-based value converted by using .y=Mx+B - Fixed: Fixes to LCD Code defects identified in code review were incorporated - Fixed: Some strings on LCD were formerly displayed improperly on LCD - Fixed: Increased total SDR record length to 0x48h from 0x40h to accommodate the S4600LH SDR requirements - Fixed: S1600JP: Corrects the baseboard temperature sensor mapping so that it works - Fixed: After forcing a CATERR on S4600LH, the debug information from Embedded Web Server lacks some information - Fixed: LAN channel cannot get DHCP IPv4 address after disabling VLAN on it - Fixed: NMI sensor event isn't logged after issuing "chassis control" command to trigger NMI - Fixed: SUT hang at POSTCODE: 0x63 while BMC LAN connected to a switch loop environment - BMC would freeze under heavy network traffic loads (e.g. broadcast storm) - Fixed: S4600LH: Fan speed reading not correct - Added other chassis support in S4600LH and corrected RPM calc - Also updated S1400FP/S1400SP SDR to reflect change. - Fixed: Network Interface hold time was out of spec for S2600GZ/S2600GL and S2400BB - Fixed: Issuing incorrect "Set CR Configuration" command returns wrong error code - Fixed: LCP error messages are not scrolling automatically without pressing LEFT and RIGHT keys - Fixed: LCP default banner text when server with normal health is displaying some junk characters at the end - Fixed: Number of characters displaying in LCP display is only 16 but it should be 18 characters - Fixed: LCP displays "No BIOS POST C" when enter into LPC under VIEW menu - Fixed: Unable to view the entire IP or Gateway or Subnet addresses using LCP display, last digit is missing during display. - Fixed: Firmware information contents in LCP displaying does not match the actual version - Fixed: Banner text is not reflecting correct information after selecting SM, LPC, or POW as a banner - Fixed: LCP default screen after power on is not the correct banner text - Fixed: S2400SC shows no socket present in CPU information page of Embedded Web Server - SMBIOS rev 2.7.1 added additional socket types. This change adds those types to the SMBIOS translation tables. - Fixed: Updated S4600LH SDR to resolve issues where fans specified in FCT SDRs couldn't be controlled with fan domains. - Fixed: BMC 1.08 S4600LH SDR was missing Sensor 0x2C (Riser 2 Left Forward Temperature) - Fixed: Exit Air Temp reading mismatch when using IPMI command under Linux - The sensor initialization code was checking both assertion and deassertion enables and settable/readable thresholds before actually setting the thresholds. This was causing the Exit Air Temp sensor to fail to set thresholds (all thresholds became 0) - Fixed: Host name is not included in Email Alert subject line - Subject line could potentially be set before host name was set. This change sets the subject line again after the host name is changed - Fixed: BMC FW must satisfy open source advertising clause for OpenSSL - Added "About" button to top bar to satisfy item 6 in the OpenSSL license. - Added: Changed SDR of S2600CP, S2600CO, W2600CR/S2600IP, and S2400GP to add Dynamic Power Unit Redundancy Sensors - Added: Add S1600JP and S2600WP PCIeSlotMap Table - Added: Adds option (0xfe) for SlotIPMB command to ignore mux completely - Fixed: Update FRUSDR packages to following versions: - S1600JP: S1600JP_FRUSDR_0.03 - S1400SP: S1400SP_FRUSDR_01 - S2400LP: S2400LP_FRUSDR_0105 - S2400SC: S2400SC_FRUSDR_0104 - S2400BB: S2400BB_FRUSDR_08 - S2400EP: S2400EP_FRUSDR_03 - S2600WP: S2600WP_FRUSDR_1.03 - S1600JP: S1600JP_FRUSDR_0.04 - S4600LH: S4600LH_FRUSDR_11 - Note: Testing with BIOS/2050_Package.zip (2.05 BIOS) with ME 02.01.05.091 UBoot increments to 1.11 in this release due to changes in LCD handling - Fixed: S2400EP: Add one additional 250ps delay for Tx clock and MAC0 drive strength to improve Signal Integrity on S2400EP - Fixed: Fixed a case that had been missed for LDAP login to EWS. - Fixed: uboot not updated after BMC FW updated when BMC executing from uboot - Fixed: Wrong DIMM location is displayed in Embedded Web Server when a non-working DIMM is populated - Fixed: Fixes to LCD module to address occcasional failures in Fan Speed Control tests. - Fixed: LED control and status changes for S1400FP and S1400SP. - Fixed: Updated the text output of ews-oem-tools to match documentation - Fixed: Channel 1 or channel 2 LAN cannot ping through with IPV6 address when the LAN cables are both installed. - Fixed: Corrected typoes in Embedded Web Server online help page. - Fixed: S2400LP: After successful issue command to load BMC configuration default, "shutdown policy" option is not set to "disabled" which is the default - Fixed: LCD SN [Server Name] displays different values at VIEW menu and SN as a banner - Fixed: S2400BB: System Fans are constantly boosting and all sensors = OK - Fixed: Updated S1600JP SDR to 0.03 - Fixed: Updated S1400SP GPIO table to improve Fan Tach reading. - Fixed: BMC was sending PMBus command to non-supported CR feature PSU. - Fixed: Update S4600LH SDR and associated zip to sync with latest FSC sheet Rev0.5,Version (v6) - Fixed: Removing 1600 W S2 PSU FW image from the BMC. - Fixed: S4600LH: Added debug to identify cause of system resets after CATERR. - Fixed: IPv6 not working when 2 NCSI channels enabled or Failover is enabled: - Fixed: There is an error message on Virtual Front Panel page when logging into the Embedded Web Server with user privilege. - Fixed: Virtual Front Panel power LED always solid green when system is in s1 state. - Fixed: Event description different when viewed in Embedded Web Console vs. when saved via EWC. - Added decode of OEM event type 0x70, sensor type 0x2B events. - Fixed: Embedded Web Server user disappears when privilege is set to 5 using ipmitool. - Fixed: BMC unresponsive when added all the users and then deleted all the users from Embedded Web Server - Added: Added S1600JP to initial platform list - Added: Add zlib license info to OEM Embedded Web Services documentation. - Added: OEM Command to enable/disable BMC Services. This implements a command to enable/disable BMC Services and another to get current state. Currently controls sshd (SMASH), Web Console, and rKVM. ** NOTE: THERE IS A CHANGE TO THE PASSWORD SYSTEM USED BY SSH AND SMASH. - As a result SMASH users may be informed of a possible security attack, by the utility, when they first log in after updating. This is not an attack, it is an update which will take place once. - Fixed: Updated S1400SP SDR, update SAS module presence sensor number to 0x2d - Fixed: S2400BB - Default and FCT version 0.07 SDR files provided. - Fixed: Update FRUSDR package (and defaults) for S4600LH to revision 08 - Fixed: Updated SDRs for S4600LH platform: - Modified and added SDR - Modified HSBP temp SDR threshold values - Corrected problem with S4600LH FRUSDR with Other chassis options that was causing system fan issues. - Some of the sensor numbers used were the same as other platforms, resulting in some erroneous displays of processor fan info. The Sensor numbers have been changed to avoid conflict - Fixed: Adding S1400FP SDR. Updates S1400FP and S1400SP DIMM offsets in the web display, and also adds information on S1400FP Fan Fault LED. - Fixed: BMC sshd password set to invalid by default - Fixed: Additional support for SSL - spec requires that user can upload both certificate and private key, now supported - Fixed: Update U-boot version to 1.8 - Fixed: BMC boot up had a window where BMC HW watchdog was not enabled. - Changed to 4 minutes so that if BMC fails to start, the hardware watchdog will trigger. - Fixed: When the BMC reboots with an active SOL session, the SOL mux was not automatically reset to redirect serial data out the system serial port. This prevented both SOL and system serial from working. Now resets SOL mux at BMC boot to prevent this situation. - Fixed: The PET Acknowledge command was requiring an open IPMI session. As per IPMI spec, this command will be sessionless and belongs to same class as Get Channel Authentication capabilities. - Fixed: Enter Firmware Transfer Mode will generated a unexpected log about FW update status - Fixed: When Exit FW transfer happens after the download of the image (i.e aborted before programming), the update failure sel event was not logged - Fixed: HSBP unresponsive after FW update. - Fixed: HSBP FRU information was sometimes unreadable via IPMITOOL. - Fixed: Combined both debug files into a single zip. Passwords on individual files are unchanged. Container zip has no password. Modified system debug commands to only accept log type 0x00 as a parameter, since there is now only one file generated. - Fixed: BMC disk drive numbering scheme does not match LSI tools (RWC2 and webBIOS) numbering scheme and marketing’s documentation - The BMC was using 1 based drive numbers, while documentation specified 0 based numbers. This change implements the changes for S2600GZ/S2600GL SDR as well as internaming conventions for the sensor numbers. - Fixed: HSBP Drive Slot Sensors report drive removal and insertion on every warm reboot - Fixed: GRUB serial terminal causes BMC distress - Fixed: Get DIMM Offset command was rejecting any DIMM number greater than 48 with completion code 0xCC. - Added: "Get drive fault LED status" and "Set drive fault LED status" IPMI commands - Added: All files required to support the add-in LCD hardware on S2600CP, S2600GL, and S2600GZ have been added. User can now plug in module and traverse the LCD menus by pressing the buttons provided on the LCD hardware module. Note: The update package provided for this release was validated with BIOS release x045. - Fixed: Patch fixes a problem with excessive Power Supply SEL events for 1200W power supplies. - Fixed: Update cipher suite LAN parameters to be consistent with IPMI spec - Fixed: Update S2400LP SDR for factory build, FAN4a~6b was added - Fixed: Changed Node Manager SEL entry descriptions. - Fixed: Update for S2400LP to solve the FAN5a~6b reading zero issue reported by the factory. - Fixed: Update S2400EP Default SDR - Fixed: Add more thorough checking to Embedded Web Server action image validation - Fixed: Update SDR on slave node, PSU temp sensors will be in Disabled status, while other PSU sensors are correct - Fixed: A failed node can't be power-offed gracefully by BMC when there is a simulated critical event of a temp sensor and stopped ystem fan. - Fixed: "Shutdown Policy" available after BIOS update - BMC returned the wrong completion code of 'get shutdown policy' command on non-halfwidth platform. - Fixed: Allow OEM Embedded Web Server image to be completely removed to factory settings - Fixed: SNMP alert and Email alert can't be received when node manager power policy defined threshold is exceededon S2400EP - Fixed: The status LED will be solid amber for a while after an AC cycle on S2400EP, S1400FP, and S1400SP. - Fixed: S2400LP DIMM event SEL does not match with the location in the board. - Fixed: Sometimes the minimum power reading is 0W on the power statistics page - Fixed for all platforms. - Fixed: Unexpected results with PS fault condition(FP Status LED, BMC Sensors) - Fixed: Slow Fan Limit event verification failed on 1200W PSU - Failed Power Supply status was not being maintained. Will not clear the PS Fault status until the Power Good is negated. - Fixed: Read platform debug command after exitng the debug log file transfer mode, the response is failed - Fixed: BMC may hold IPMB CLK low after BMC reset if the BMC is addressed over IPMB and the BMC resets before that I2C transaction completes. - Fixed: BB +1.1V STBY low critical log during DC off - The 1.1V Stby voltage sensor was generating events when the power button was held in over 4 sec. - Fixed: Emulex* Pilot III P02 Chip - Prefetchable bit (BAR10-BIT3) is not set for memory range. - Fixed: S4600LH: Add Memory Trip support for CPU 3 and CPU 4 - Fixed: S4600LH: Updated SDR version to 08. - Fixed: S4600LH: Fixed the System Fans reading. - Fixed: Incorporated generally released Linux driver fixes for bonding-related bugs, glitches, etc. - Fixed: The cramfs tools used in Embedded Web Server image were licensed as GPL, these have been rewritten. In more paranoia was added in image creation, throwing errors if anything but regular files are in the source directory. This prevents symlink and device node attacks. Also added is code to allow for building .deb, .rpm and .msi install packages. Currently the windows installer only does 32-bit, but the linux packages are available in both 32- and 64-bit varieties. Some of these changes are outlined in the updated user document that gets distributed with the binary. - Fixed: Corrects a reaction to bad OEM records in SDR. Previously, this would report an error and reset the entire SDR with default values. This is not required, and the delete step will no longer happen. - Fixed: Modified uboot handling of Enter FW Transfer Mode command to return completion code 0x80 (already in FW transfer mode) if the Enter FW Transfer Mode command has been sent previously. - Fixed: 1200W power supplies were generating spurious Fan Failure events. - Fixed: HSBP FW crash during firmware image updates. - Fixed: PS temperature cannot be read after power cycling over night. - Fixed: BMC boot up has a window where BMC HW watchdog is not enabled -BMC HW WDT was defaulted to trigger after 18 hours. This default timeout has been changed to 4 minutes. - Added: Add a software-only method to replace public key and API to query key info Note: The update package provided for this release was validated with BIOS release x045. - Fixed: Update default SDR of S2600CO to version 1.04. Update default SDR of W2600CR/S2600IP to version 1.03. Update default SDR of S2400BB to version 0.06. - Fixed: Updates PSU FW for 460W CRPS PSU to DPS-460KB A S3 3.09.29 - This version contains a fix to set the SMBALERT interval to 30 seconds. - Fixed: Insert two DIMMs on channel A1 and A2, and inject an ECC error at A1, the event log will record correctable ECC at B1. - S2400GP: The channel number for DIMMS on channel A1 and A2 were being recorded incorrectly as being channel B1 when correctable ECC errors were injected. - Fixed: Sometimes the minimum power reading is 0W on the Embedded Web Server power statistics page. - For S2400SC ME must receive a Reset NM Statistics command upon entering ACPI state S0 to get an accurate minimum power reading. - Fixed: The Hex data of the sel event retrieved by Intel(R) Hybrid Cloud (IHC) is different from those in selviewer. - Fixed: Execute Get DIMM info command to check Empty slot response "0x03" - Per EPS an empty DIMM slot should return 0x83 but was returning 0x03 - Fixed: Perform Action Button is disabled when Graceful OS shutdown option is used in Embedded Web Server - The Graceful OS Shutdown action caused the "Perform Action" button in the Embedded Web Server to be disabled during the process, however it wasn't re-enabled until the user reloaded the page. This change disables the button after any action, and re-enables the button after any power-control action completes. - Fixed: Embedded Web Server Remote Control Page - Message is not consistent across all pages for a User with USER privilege. - Embedded Web Server Remote Control Page: Remote KVM is not available except to users with ADMIN or better privileges. The informational message was not consistent across all pages for a User connected with USER privilege. Logging into the EWS with a non-admin user, and attempting to open an Remote KVM window, will now redirect to a page explaining this. The help page has also been updated with this information. - Fixed: KVM - Help Button - About "Jviewer" copyright statement is wrong. - The copyright date presented by JViewer in the Help->About interaction should now show copyright 2011 rather than 2005. - Fixed: Embedded Web Console: Node Manager page hard shutdown does not seem to be a hard shutdown. - According to the Node Manager documentation, a hard shutdown is used but NM actually attempts a graceful shutdown first, only performing the hard shutdown if the graceful shutdown stalls for 30 seconds. The Embedded Web Server description and help page should correctly indicate that this is the expected behavior. - Fixed: Get Chassis Status command identify LED with wrong status - The Get Chassis Status command was not returning the correct "Identification LED" status. - Fixed: Fans stay boosted after BMC force update followed by SDR update - Fans should no longer boost after updating the SDR after a forced FW update. - Fixed: Empty or Unconfigured HDD will continuously report faulty or assert/deassert - Fixes an issue where a system with ESRTII RAID 5, configured with three HDDs and a fourth installed but set either unconfigured or global-hot-spare, would generate numerous spurious drive fault errors to the System Event Log. - Fixed: Firmware hang if BMC is crashed one time and BMC cold reset is executed 3 times after a crash within 30 minutes. - Fixed: There is a typo error in BMC WebUI help document for "Alert Email" sub-menu - Added: Adds new de-pop PBA (G49054-XXX) for S2600JF. Halfwidth projects will auto load de-pop SKU SDR when PBA# of FRU is G49054-XXX. Note that this release is intended to fix a single issue for the S2400SC platform. It was provided only for that platform. - Fixed: On S2400SC, sometimes the minimum power reading is 0W on the Embedded Web Console power statistics page. ================================================================================ FRUSDR Changes since release 1.02 ================================================================================ - Follow Granite Pass FSC config sheet Rev (2.9). - S2400GP.sdr: Modify "front panel" FRU Entity ID from 0x07 change to 0x0C. - S2400GP.sdr: Modify "front panel" FRU Entity Instance from 0x37 change to 0x01. - S2400GP.sdr: Modify "Baseboard" FRU Entity Instance from 0x36 change to 0x01. - S2400GP.sdr: Modify "SAS Module" FRU Entity Instance from 0x31 change to 0x01. - S2400GP.sdr: Add SDR Type 11 Record "Pwr Supply 1 FRU". - S2400GP.sdr: Add SDR Type 11 Record "Pwr Supply 2 FRU". - S2400GP.sdr: Add SDR Type 11 Record "HS Backplane 1". - S2400GP.sdr: Add SDR Type 11 Record "HS Backplane 2". - S2400GP.sdr: Add SDR Type 11 Record "HS Backplane 3". - Follow Granite Pass FSC config sheet Rev (3.0). - Update FRUSDR utility Version 11.0 Build 9. - S2400GP.sdr: Modify HDD number. - S2400GP.sdr: Add SAS Module Presence. - Follow Granite Pass FSC config sheet Rev (3.1). - Update FRUSDR utility Version 11.0 Build 11. - S2400GP.sdr: Power unit redundancy sensor "Capabilities" change to 00. ============================================================================= LEGAL INFORMATION ============================================================================= Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Intel is a registered trademark of Intel Corporation. *Other names and brands are the property of their respective owners. Copyright (c) 2012 Intel Corporation. A portion of this firmware is open source code, which falls under the GPL 2.0 license. [END OF RELEASE NOTES]