This release note and the software that accompanies it are copyright (c) 2014 Intel Corporation or its suppliers, and may only be installed and used in accordance with the license that accompanies the software. This Software is furnished under license and may only be used or copied in accordance with the terms of that license. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. The Software is subject to change without notice, and should not be construed as a commitment by Intel Corporation or its suppliers to market, license, sell or support any product or technology. Unless otherwise provided for in the license under which this Software is provided, the Software is provided AS IS, with no warranties of any kind, express or implied. Except as expressly permitted by the Software license, neither Intel Corporation nor its suppliers assumes any responsibility or liability for any errors or inaccuracies that may appear herein. Except as expressly permitted by the Software license, no part of the Software may be reproduced, stored in a retrieval system, transmitted in any form, or distributed by any means without the express written consent of Intel Corporation. ========================== Supported RAID Controllers ========================== Intel(R) Integrated RAID modules RMS2LL080 and RMS2LL040 Intel(R) RAID controller RS25GB008 and RS25FB044 Intel(R) Integrated RAID Module RMS25JB040, RMS25JB080, RMS25KB040, RMS25KB080, RMS25LB, and RMS25LB080 Please verify that this utility has been tested with the RAID card/module you have chosen to use by checking the drivers web page for your controller at http://WWW.intel.com/support/ =================== Package Information =================== Driver Version = 20.0-2.00.75.00 OS supported = Windows* 2008 & (x86, x64) Windows* 2008 R2 (x86, x64) Windows* 7 (x86, x64) Windows* 8 (x86, x64) Windows* 8.1 (x86, x64) Windows* 2012 (x64) Windows* 2012 R2 (x64) ========= Attention ========= Please see the read me file in each release subdirectory for special instructions specific to that Windows version. ================== Known Restrictions ================== N/A ======================= Contents on the package ======================= The following files(or folders) are included in this package: Name Description SAS2_ITIR_Windows_DRV_ph20_readme.txt This file License_v2.pdf License file /Win2K8 x86 and x64 version drivers for Windows* 2008 /Win7_2K8R2 x86 and x64 version drivers for Windows* 7 and Server 2008R2 /Win8_2K12 x86 and x64 version drivers for Windows* 8 and Server 2012 /Win8.1_2K12R2 x86 and x64 version drivers for Windows* 8.1 and Server 2012R2 ========================= Installation Instructions ========================= This updated driver can be applied using the normal OS installation options. The following procedure describes how to install Windows 2012/2008/7/8/8.1 system onto RAID logical disk: 1. Copy the driver files to a removable media, such as USB flash drive, CD-ROM, or floppy disk 2. Create RAID logical disk(s) using MPT OpROM Config Utility (during POST). 3. Boot Windows installation disk. Follow instructions on screen until below step is reached. 4. At "Which type of installation do you want?" screen, select "Custom (advanced)" 5. At "Where do you want to install Windows?" screen, select "Load Driver" 6. Install the removable media with the driver files (extracted in step 1) 7. Select "Browse" and locate the folder with the driver files and then select "OK" 8. Select "Next". There may be a 1-2 minute delay as drivers are loaded. 9. Select "Drive options (advanced)" to customize partitions - if necessary 10. Select "Next" to continue with the installation 11. There are several reboots during installation - ensure that the selected RAID array is the boot device during every reboot. ================ Installation of the driver after the operating system is installed: 1. Boot into applicable Windows OS. Click the Windows Start button and select Settings. 2. Click Control Panel. 3. Select Adapter. 4. Select the Drivers tab. 5. Scroll down the list until the appropriate selection for your system which contains the MPT SAS2 driver for your operating system displays, then click . 6. Select it, then remove it by clicking the Remove button. 7. Click the Add button. 8. Select the Have Disk button. 9. Insert the diskette or flash drive. 10. Select drive letter A: and click on . 11. Select MPT SAS2 and click OK. 12. After Windows* copies the driver, reset the system. ================== Component Features ================== N/A ============ Known Issues ============ N/A ============= Fixes/Updates ============= version 20.0-2.00.75.00 1. Removes support for Windows* XP, 2003 and Vista. version 19.0-2.00.72.02 1. Resolves restart loop issue on Microsoft* Windows* 8.1 and Windows* Server 2012 R2 storage drivers if the Microsoft Windows Update Rollup 2919355 (April 2014) has been installed. 2. Driver will send over temperature message to system event log when threshold exceeded 3. Implements Unit Attention Reset for multi-initiator environments 4. Peformance improvements for high CPU utilization workloads version 17.0-2.00.66.02 1. Initial release for Windows* 8.1 and Server 2012R2 2. Adds support for Standby Immediate version 15.0-2.00.60.00 1. Initial public release for for Intel(R) SAS Controller RS25LB040/80 version 14.0-2.00.58.00 1. Initial release for Win8 and Server 2012 only version 13.5-2.00.55.01 1. Initial release for for Intel(R) SAS Controller RS25FB044 version 11.0-2.00.49.01 1. Initial release for Intel(R) Integrated RAID Modules RMS25JB040, RMS25JB080, RMS25KB040 and RMS25KB080 version 10.0-2.00.45.01 1. Package supports RS25GB008 and RMS2LL0x0 version 8.0-2.00.37.00 1. Initial release for for Intel(R) SAS Controller RS25GB008. version 7.0-2.00.35.00 1. Posting IOCTL while not in Operational state 2. Add Intel RES2SV240 to windows lsinodrv.inf 3. Windows driver INF changes to support Intel unique identification in Device Manager when Intel Subsystem IDs are detected. Version 5.0-2.00.20.00_upd_2010.07.06 1. Updated XP drivers to 5.0-2.00.21.00 and added 32 bit WHQL 2. Changed README file name Version 5.0-2.00.20.00 1. Initial release for RMS2LL080 and RMS2LL040 *Third-party trademarks are the property of their respective owners.